Air King AS54 Hoja de instrucciones descargar pdf (Pagina 2)

INSTALLATION INSTRUCTIONS

CAUTION:

MAKE SURE POWER IS SWITCHED OFF AT

SERVICE PANEL BEFORE STARTING INSTALLATION.

SECTION 1

Preparing the Exhaust Fan

1. Unpack fan from the carton and conﬁrm that all pieces are present. In addition to the

exhaust fan you should have:

1 - Grill

1 - Damper Assembly (attached)

1 - Knockout Plug

1 - Instruction/Safety Sheet

2. Remove the fan’s venturi assembly, which is secured in place with one screw through the

venturi (Figure 1). This is a captive screw and will stay installed in the venturi. Keep the

venturi assembly and the grill in the carton until needed so they do not get damaged or lost.

3. Choose the location for your fan. To ensure the best

air and sound performance, it is recommended that

the length of ducting and the number of elbows be

kept to a minimum, and that insulated hard ducting

be used. Larger duct sizes will reduce noise and

airﬂow restrictions.

4. Select the most convenient electrical knockout hole

and insert the knockout plug into the 2nd knockout

hole (Figure 2).

SECTION 2

New Construction

1. Using the gauge on the fan’s housing (Figure 3), line up housing so that it will be ﬂush with

the ﬁnished ceiling or wall. Position the fan so that the tabs rest ﬂat against the joist or stud

and secure with four nails (not provided) to ensure proper installation.

SECTION 3

Existing Construction

1. Position housing against the joist or stud and trace an outline of the housing onto the

ceiling/wall material (Figure 4). Set housing aside and cut opening, being careful not

to cut or damage any electrical or other hidden utilities. Place housing next to the joist

or stud and insure that it is ﬂush with the ﬁnished ceiling. Secure with four nails (not

provided) to ensure proper installation (Figure 3).

www.airkinglimited.com

210572050 Rev. H 12-15 2 of 8

SECTION 4

Ducting

CAUTION: ALL DUCTING MUST COMPLY WITH LOCAL AND NATIONAL

BUILDING CODES.

1. Connect the ducting to the fan’s duct collar (Figure 4). Secure in place using tape or

screw clamp. Always duct the fan to the outside through a wall or roof cap.

NOTE: If damper detaches from unit, reattach by snapping the collar back onto the unit. It is

designed to only ﬁt one way.

SECTION 5

Wiring

CAUTION: MAKE SURE POWER IS SWITCHED OFF AT

SERVICE PANEL BEFORE STARTING INSTALLATION.

CAUTION: ALL ELECTRICAL CONNECTIONS MUST BE

MADE IN ACCORDANCE WITH LOCAL CODES, ORDINANCES, OR

NATIONAL ELECTRICAL CODE. IF YOU ARE UNFAMILIAR WITH METHODS OF INSTALLING

ELECTRICAL WIRING, SECURE THE SERVICES OF A QUALIFIED ELECTRICIAN.

1. Run wiring from an approved wall switch carrying the appropriate rating. One neutral (white),

one ground (green or bare copper), and one hot (black lead connected to the switch). Secure

the electrical wires to the housing with an approved electrical connector. Make sure you

leave enough wiring in the box to make the connection to the fan’s receptacle.

2. From where you have access to inside the fan’s junction box, connect the White wire from

the house to the White wire from the fan’s receptacle. Connect the Black wire from the

wall switch to the Black wire from the fan’s receptacle. Connect the ground wire from the

house to the Green wire from the fan’s receptacle (Figure 6). Use approved methods for

all connections.

Figure 1

Figure 2

Figure 3

Figure 4

Figure 5

Supply

from

house

Figure 6

White

Hot (Black)

Ground

1 2 3 4 5 6 7 8

Comentarios a estos manuales

Sin comentarios

Air King AS54 Hoja de instrucciones Pagina 2

Comentarios a estos manuales

Relacionado con productos y manuales para No Air King AS54